Keeping Birria Tacos from Getting Soggy
How to keep birria tacos crisp: drain the filling, fry tortillas in consommé fat, build quesabirria fast, and serve consommé for dipping on the side.
Contents
- Drain the birria filling well
- Fry tortillas in consommé fat
- Assemble quesabirria quickly
- Questions About Soggy Birria Tacos
- How do you keep birria tacos from getting soggy?
- Should you dip the tortilla in consommé before frying?
- Why do my birria tacos fall apart and turn soft?
- Can you make birria tacos ahead of time?
Keeping birria tacos from getting soggy comes down to water control at three points: the filling, the tortilla and the moment of assembly. Birria is a braised meat dish, so its shredded filling carries a lot of liquid, and a corn tortilla left in contact with that liquid softens within moments. The fix is to drain the meat, give the tortilla a fat barrier and keep the dipping consommé out of the taco until someone eats it. Each step below is small, and together they decide whether the shell stays crisp.
Drain the birria filling well
Birria filling moisture is the main reason a taco softens from the inside, so pull the meat from the pot with a slotted spoon and let it drain. Shred the meat in a wide bowl and leave the juices behind rather than pouring them over the tortilla. If the shredded meat still looks wet, press it gently in a sieve or warm it briefly in a dry pan to drive off surface liquid. A dry-ish filling still tastes of the adobo, and the consommé served alongside restores the moisture at the table.
Fry tortillas in consommé fat
Frying tortillas in consommé fat gives the tortilla a water-resistant layer and firms it before the filling arrives. Skim the reddish fat from the top of the consommé, heat a thin film in a skillet and pass each corn tortilla through it for a few seconds on each side. The tortilla should turn pliable and glossy, not brittle, because a cracked shell lets liquid straight through. Set the fried tortillas on a rack rather than a stack of paper, where trapped steam softens them again.
Assemble quesabirria quickly
Quesabirria adds melted cheese, which is a second source of moisture, so build each one close to serving and keep the layers in order. Place cheese against the hot tortilla, add the drained birria on top and fold the shell so the meat sits inside the cheese. A cheese crust that forms against the pan seals the fold and holds the filling away from the lower tortilla surface. Hold finished tacos in a single layer in a warm oven, never piled, so steam can escape instead of soaking back in.
Questions About Soggy Birria Tacos
How do you keep birria tacos from getting soggy?
Keeping birria tacos from getting soggy means removing liquid before it reaches the tortilla. Drain the shredded birria, fry the tortillas in skimmed consommé fat and add the dipping broth only at the table. Serve each taco as soon as it is built, because a filled taco left sitting softens even when the filling is dry.
Should you dip the tortilla in consommé before frying?
No, dipping a tortilla in consommé before frying adds water exactly where you do not want it. Use the fat skimmed from the top of the consommé to fry the tortilla instead, which creates a barrier without soaking the corn. Keep the consommé itself in a bowl for dipping the finished taco by hand.
Why do my birria tacos fall apart and turn soft?
Soft birria tacos usually come from an overloaded filling and a tortilla that was never firmed in fat. Use two tortillas or a single larger one, keep the meat drained and fold while the shell is hot. Overfilling also breaks the fold, and a broken fold lets liquid escape onto the outside of the taco.
Can you make birria tacos ahead of time?
Yes, the parts can be prepared ahead, but the assembled taco cannot wait long. Cook and shred the birria, cool it and store it separately, and fry the tortillas just before serving. Reheat the meat until it steams, drain it once more and build the tacos when guests are at the table.