How to Choose and Set Up a Tortilla Press

Learn what to look for in a tortilla press and how to put it together. Get steps for first use, pressing technique, and simple upkeep.

6 min read0 viewsHow to Choose and Set Up a Tortilla Press
— · 0 votes
Contents
  1. What Makes a Good Tortilla Press
  2. Tortilla Press Materials and Plate Size
  3. Tortilla Press Assembly and First Setup
  4. Lining the Plates for Easy Release
  5. Pressing Technique for Even Tortillas
  6. Where to Place Your Tortilla Press
  7. Cleaning and Simple Upkeep
  8. Tortilla Press Questions Answered
  9. How do I set up a Victoria tortilla press?
  10. How do you put a tortilla press together?
  11. Do I need to season a new tortilla press?
  12. What can I use instead of parchment paper in a tortilla press?
  13. Why does my tortilla stick to the press?

A tortilla press turns a ball of masa dough into a flat round ready for the comal. Choosing one comes down to plate size, material, and how the press feels on your counter. Setting it up takes only a few minutes before the first press.

What Makes a Good Tortilla Press

A good tortilla press has flat, parallel plates that meet evenly under the handle. The hinge should move without wobble and hold the top plate in line with the base plate. Press plates that close squarely give you an even thickness from edge to edge.

The handle needs a comfortable grip and enough leverage to flatten masa dough with one smooth motion. On a sturdy press the handle does not flex or bend when you push down. Look for a model that sits stable on the counter without sliding.

Weight matters because a heavier press tends to stay put while you work. A light press can still perform well if the base has a wide footprint. The finish on the plates should feel smooth and release the dough without sticking.

Tortilla Press Materials and Plate Size

Cast iron presses are heavy and strong, and they hold up to steady use in a home kitchen. An aluminum press is lighter and easier to move but still presses a thin tortilla. A wooden press works well for many cooks, though the plates absorb less heat than metal.

The Victoria tortilla press is one well-known cast iron model with a simple lever design. Its plates come in several diameters, often between six and ten inches. The size of the press plates sets the size of the tortilla you can make.

Smaller plates suit taco-sized tortillas, while larger plates allow burrito or quesadilla sizes. Choose a press that matches the width of tortillas you plan to cook. A plate that is too small for the dough ball will squeeze masa out the side.

Tortilla Press Assembly and First Setup

Many presses arrive fully assembled, but some models need the handle attached to the hinge. Line up the holes on the handle with the hinge pivot and insert the pin or bolt. Tighten the fastener so the handle moves freely without side play.

Place the assembled press on a dry, flat section of counter near your work area. Keep the base plate flat and the handle pointed toward you or to one side. The weight of a cast iron press helps it sit still during pressing.

Wash the press plates with warm water and a soft cloth before the first use. Dry the plates fully to prevent rust on cast iron. No oil or seasoning is needed on a modern tortilla press.

Lining the Plates for Easy Release

A parchment or plastic liner keeps the masa dough from sticking to the press plates. Cut two squares slightly larger than the press plates from a food-safe plastic bag or parchment paper. Place one liner on the base plate and set the dough ball in the center.

Lay the second liner on top of the dough before lowering the top plate. The liner should cover the entire dough area and extend past the edges. This method lets you peel the pressed tortilla off without tearing it.

Replace the liners when they become wrinkled or coated with dried masa. You can reuse sturdy plastic squares for one session of pressing. Parchment sheets tear more easily but still work for a few presses.

Pressing Technique for Even Tortillas

Roll the masa into a ball about the size of a golf ball for a standard taco tortilla. Center the ball on the lined plate and fold the top liner over it. Lower the handle with steady pressure until the plate stops or the dough reaches even thinness.

Open the press and rotate the tortilla half a turn between the liners. Close the press a second time with lighter pressure to even out the edges. The tortilla should be thin enough to see the texture of the liner through the dough.

Peel the top liner away slowly, then lift the tortilla with the bottom liner still attached. Drape it onto a hot comal or griddle by flipping the liner over. The tortilla releases from the liner in one piece.

Where to Place Your Tortilla Press

Counter placement matters for comfortable pressing and a stable setup. Put the press on a dry, low counter so you can push the handle down without reaching high. The base plate must lie flat against the surface with no gaps underneath.

A press near the stove or comal keeps the dough moving from ball to tortilla to heat. Keep the area dry because moisture makes cast iron and wooden presses slippery. The press does not need to be bolted or clamped to the counter.

Store the press on the counter if you use it often, or put it in a cabinet after it cools. Protect cast iron from humidity to avoid surface rust. A dry cotton cloth draped over the press keeps dust off the plates.

Cleaning and Simple Upkeep

Clean the press after each use with a dry cloth or a slightly damp cloth. Never submerge a cast iron or wooden press in water. Brush off any dried masa bits before they harden on the plates.

Dry the press completely before you store it, especially around the hinge and handle joint. A light wipe with food-grade mineral oil can protect a cast iron plate from rust. The oil film should be very thin and wiped away before the next use.

Check the hinge occasionally for loose screws or pins and tighten them by hand. A press that works smoothly needs no replacement parts for many years. When cared for, a good press stays in service indefinitely.

Tortilla Press Questions Answered

How do I set up a Victoria tortilla press?

Place the cast iron base on a flat, dry counter and attach the handle to the hinge if the press ships in two pieces. The handle slips onto the hinge pin and secures with a screw or pin. Wash and dry the plates, then add parchment or plastic liners before the first use.

How do you put a tortilla press together?

Line up the handle with the hinge pivot and insert the pin or bolt through both parts. Tighten the fastener enough to remove extra movement but not enough to bind the handle. The press is ready when the plates open and close without wobble.

Do I need to season a new tortilla press?

A modern tortilla press does not need seasoning before use. The plates are seasoned if the model is made of raw cast iron, but many presses have a protective finish from the factory. Wipe the plates with a dry cloth and use liners to keep masa from sticking.

What can I use instead of parchment paper in a tortilla press?

A food-safe plastic bag cut into two squares works well and lasts longer than parchment. Both sides of the dough are covered so the press plates stay clean. Heavy plastic from a freezer bag resists tearing better than thin produce bags.

Why does my tortilla stick to the press?

The dough sticks when the press plates are dry or the liner is too small. Use a liner that extends past the tortilla on all sides and make sure the dough is not too wet. Press with one smooth motion and peel the liner off slowly before lifting the tortilla.

Latest articles