# Slow Cooker Taco Seasoning for Ground Beef

How to season ground beef for slow cooker tacos: when to add taco seasoning, how chili powder and cumin work, and how to keep the filling from drying out.

Slow cooker taco seasoning for ground beef is a mix of spices stirred into browned meat and left to cook gently, so the filling stays moist and the flavor deepens. The spice blend does the work while the slow cooker holds the heat low, and the meat turns into a soft taco filling. You control the salt, the heat and the balance of chili powder and cumin. The page explains when to add the seasoning, how much liquid the pot needs and how to adjust the mix. 

## When to add the seasoning 

Taco seasoning goes into the slow cooker after the ground beef has browned in a skillet on the stove. Cooking the meat first lets you pour off the fat and gives the spices a hot surface to open up on. Add the chili powder, cumin and other spices with the liquid once the meat is in the crock, then stir so every crumb is coated. Seasoning at the start lets the flavors blend through the whole cooking time. 

## Building the spice blend 

A [homemade taco seasoning for ground beef](/articles/small-batch-homemade-taco-seasoning-for-one-or-two/) starts with chili powder and cumin in roughly equal amounts, then adds garlic, oregano and a little salt. Chili powder brings color and mild heat, while cumin gives the earthy note people recognize in taco meat. A low sodium seasoning lets you salt at the end, which suits a slow cooker because the liquid reduces and concentrates salt. Mix the spices in a small bowl before they touch the pot so they spread evenly. 

## Keeping the filling moist 

Slow-cooked ground beef filling needs some liquid in the pot or the meat turns dry and crumbly. Add a small amount of water, broth or crushed tomato along with the spices, just enough to keep the bottom of the pot wet. Ground beef releases its own juices, so the filling will loosen as it cooks and you can stir it down before serving. Leave the lid on and keep the heat low, then taste and adjust the salt near the end. 

## Questions about slow cooker taco meat 

### Should I brown ground beef before it goes in the slow cooker? 

Yes, browning ground beef first gives taco meat a deeper flavor and lets you drain the fat before the slow cooking starts. The browned meat also holds the spice mix better than raw meat does. If you skip this step, break the meat up well as it cooks so the seasoning reaches all of it. Browned meat needs a shorter time in the pot than raw meat. 

### Can I use homemade taco seasoning in a slow cooker? 

Yes, homemade taco seasoning works well in a slow cooker and lets you set the salt and heat yourself. Make the blend from chili powder, cumin, garlic, oregano and salt, then stir it into the browned beef with a little liquid. A homemade mix has no fillers, so taste the filling near the end and add more if the flavor is flat. Store any extra blend in a covered jar away from heat. 

### How much liquid does slow cooker ground beef taco filling need? 

Slow cooker ground beef taco filling needs only a small amount of liquid, since ground beef gives off its own juices as it cooks. Add enough water, broth or crushed tomato to wet the bottom of the pot and coat the meat, then let the lid hold the steam in. Too much liquid makes the filling soupy, but you can uncover the pot near the end to let it reduce. Stir the meat once or twice so it cooks evenly. 

### Is slow cooker taco meat low sodium if I make my own seasoning? 

Yes, a low sodium seasoning made at home gives you control over the salt in slow cooker taco meat. Commercial blends often carry a lot of salt, so mixing your own chili powder, cumin and garlic lets you start low. Add salt in small amounts near the end of cooking, after the liquid has reduced and the flavor has settled. A slow cooker concentrates the filling as it cooks, so salt early can taste stronger later.
