# Setting Up a Rain Barrel Irrigation System

Learn how to set up a rain barrel irrigation system: hook up a hose or drip line, raise the barrel for gravity pressure, and keep water flowing to beds.

Setting up a rain barrel irrigation system means placing a barrel to catch roof runoff, fitting an outlet, and running a hose or drip line to the garden. Water flows by gravity unless you add a pump. The height of the barrel above the outlet sets the pressure you get. 

- Place the barrel on a firm, level base so it stays stable when full.
- Raise the barrel to gain gravity pressure; every bit of height above the outlet helps.
- A drip line suits low-pressure gravity flow better than a plain hose.
- Keep screens and filters in place so debris does not clog emitters.
- Shut off the outlet and drain the barrel before freezing weather.
 

## How a rain barrel system works 

A rain barrel irrigation system collects roof runoff in a barrel and releases it to a garden through an outlet near the bottom. Gravity pushes the water down and out, so no electricity is needed for a simple setup. The barrel, its base, the outlet and the line to the beds form the whole system. 

A downspout feeds the barrel through a screen that keeps leaves and grit out. Water then sits in the barrel until you open a valve or start a drip line. A gravity-fed irrigation system works because water always seeks the lowest point. 

The size of the barrel sets how much water you can store between rains. The roof area that drains to it sets how fast it fills. Match the two so a heavy rain does not overflow before you have used the stored water. 

## Choosing a spot and a solid base 

A rain barrel needs a firm, level base, because a full barrel is heavy and can tip on soft ground. Set it on a paved pad or a frame of timber and blocks that will not settle. Keep the base wider than the barrel. 

Place the barrel where a downspout can reach it and where you can run a line to the beds. Water weighs a great deal per volume, so avoid a spot where runoff could undermine the base. Check the ground after the first fill. 

Keep the barrel shaded if you can, since sun warms stored water. Warm water is fine for some plants but can stress others at the roots. A lid or screen also keeps mosquitoes from breeding in the barrel. 

## Plumbing the outlet and hose connection 

The rain barrel hose connection is the fitting near the bottom where water leaves the barrel. Fit a valve there so you can control flow and shut it off for maintenance. Seal the threads with tape made for the job so the joint does not weep. 

A hose adapter lets you attach a garden hose or a drip line to the valve. Keep the run short and the line sloping downhill so gravity can do the work. A long, flat run will lose the flow you gained. 

An overflow pipe near the top carries excess water away from the base. Route overflow to a bed or a drain so it does not erode the ground under the barrel. A full barrel with a blocked overflow can spill over the lid. 

## Getting pressure from a raised barrel 

Rain barrel water pressure comes from the height of the water surface above the outlet. Elevating the barrel for pressure is the simplest way to strengthen flow. More height gives more pressure head, which is the vertical distance water falls. 

Gravity-fed pressure head is modest compared with a household tap. Expect low pressure from a barrel sitting on blocks at ground level. Raise the barrel on a sturdy stand to gain head, and keep the stand stable and braced. 

How much water pressure you get from a rain barrel depends on the height difference, the hose diameter and the length of the run. A wider and shorter hose delivers more flow at the same height. Pumped systems can lift pressure further if gravity is not enough. 

## Running a drip line from the barrel 

A rain barrel drip line suits gravity flow because it delivers water slowly at low pressure. Pressure-compensating emitters may need more pressure than gravity gives, so match the emitters to the head you have. A simple soaker hose or a line of plain emitters works at low pressure. 

Drip irrigation from a rain barrel keeps water at the roots and wastes little on paths. Run the line along the beds and cap the far end. Flush the line now and then to clear grit that slipped past the screen. 

A filter between the barrel and the drip line protects the emitters from debris. A low-pressure drip system still needs a filter, because fine grit can block small openings. Clean the filter when flow drops. 

## Hose or drip: matching the line to the job 

A hose gives a quick soak but needs more pressure than gravity often supplies. A drip line gives slow, even water at low pressure and suits a barrel system. Choose the line by the pressure you can raise, not by what looks easiest. 

Hose and drip irrigation pressure differ in what they need. A plain hose with a nozzle works better with a pump or plenty of head. A drip line tolerates low head and keeps delivering water over a longer period. 

Use a short hose to fill a watering can when you want to water by hand. Use a drip line when you want the barrel to water beds over time without attention. Both can share the same outlet valve. 
| Line type | Pressure need | Good fit | 
| Plain hose with nozzle | Higher flow and head | Quick fills and hand watering | 
| Soaker hose | Low pressure | Short runs along rows | 
| Drip line with emitters | Low to moderate | Beds watered slowly | 
| Pumped line | Raised by a pump | Longer runs and higher output |  

## Adding a pump when gravity is not enough 

A rain barrel pump adds pressure when gravity head is too low for your line. Fit the pump at the outlet and follow the maker's wiring and safety instructions. Water and electricity together demand care, so have a qualified person handle the wiring. 

A pump lets you push water through a longer hose or a drip line that needs more pressure. It also lets you move water uphill to a higher bed. Size the pump to the flow you need and the height you must lift. 

Keep the pump intake clear of grit and never run it dry. A dry-running pump can be damaged, so fit a float switch or watch the barrel level. Shut the pump off when the barrel is low. 

## Maintenance and care through the seasons 

Rain barrel irrigation needs routine care to keep water flowing and the barrel sound. Clean the screen and filter regularly, and check the outlet for leaks. Flush the drip line to clear debris. 

Before freezing weather, shut the outlet and drain the barrel so trapped water cannot split it. Disconnect the hose and store it out of the sun. Cover or remove the barrel if ice is a risk in your area. 

Check the base and stand each season for rot or movement. A settling base can tip a full barrel, so fix it before refilling. Keep the lid secure so children and animals cannot get in. 

## Rain Barrel Irrigation Questions 

### How do I set up a rain barrel irrigation system? 

Set a barrel on a firm, level base near a downspout, fit a valve and hose adapter at the outlet, and run a hose or drip line downhill to the beds. Add an overflow pipe near the top. Raise the barrel if you need more gravity pressure. x 

### How much water pressure comes from a rain barrel? 

Rain barrel water pressure depends on the height of the water surface above the outlet. A barrel on the ground gives very little head, while one raised on a stand gives more. Hose diameter and run length also change the flow you feel at the end. x 

### Should I elevate my rain barrel for pressure? 

Yes, elevating a rain barrel for pressure is the simplest way to strengthen gravity flow. More height above the outlet means more pressure head. Build a sturdy, braced stand that will not tip when the barrel is full. x 

### Can I run drip irrigation straight from a rain barrel? 

Yes, a rain barrel drip line can run on gravity if you choose emitters that work at low pressure. Fit a filter to protect the emitters and keep the run short and sloping. Pressure-compensating emitters may need a pump. x 

### Do I need a pump for a rain barrel system? 

No, a pump is not required for a simple gravity-fed system. A rain barrel pump helps when you need more pressure for a long hose or a line that demands higher flow. Have a qualified person handle any electrical work. x
